Note: Read entire guide before starting installation.

Use common sense! This is a simple procedure. Don't do something if it doesn't seem safe or doesn't make sense to you. If in doubt, stop and seek advice from a qualified mechanic or ask for advice.

Background: As part of the original VW Vanagon Syncro design, a functionally identical device to this one was installed on those vehicles that came with a Front Diff-Lock (this was not a US option). The primary motivation was one of safety. If the front-diff knob is inadvertently pulled out to engage the front diff-lock (such as a child might do when the van is parked), the first indication to the driver (assuming he doesn't notice that the knob is out) is the front-diff dash light coming on simultaneously with the steering wheel abruptly pulling to the left or right. It will be almost impossible to steer, and if you are on pavement, you will most likely break a front axle or CV joint. This might happen just as you are pulling out of your driveway, or it might happen at 70 MPH as you get to that first big curve on the freeway. The idea is that a blinking dash light might let you know so that you can disengage it before starting your drive.

This is not a terribly complex device. It consists of a switch that hooks up to the vacuum line that connects to a circuit board. This combination of devices is able to blink the dash light when there is sufficient vacuum available at the diff-lock switch to engage the diff-lock, prior to engagement where the light comes on full.

This device provides some diagnostic functions, as well as it's primary purpose as a safety warning device. If there is a problem with the vacuum connection between the engine and the diff-lock switch, then there is not enough vacuum to either blink the light or engage the diff-lock (time to check the lines between the engine and the vacuum reservoir up to the dash). If the blinking light doesn't immediately come on, but starts blinking after a bit, and then engages, you likely have a problem with vacuum line on the dis-engage side of the diff-lock unit (between the dash switch and the control unit). If the blinking light comes on but the diff-lock does not engage as it should, then the diff-lock vacuum control unit at the differential should be checked. If neither the blinking light comes on nor the solid light comes on once engaged, then there is likely a bad bulb in the dash. If the blinking light comes on, but it just keeps blinking when the diff-lock has engaged, then there is a problem with the screw-in switch on the differential.

Add On Diff Lock Blinker Installation Guide

Although the danger of accidentally engaging the rear diff-lock is usually not so catastrophic, it can still be a nasty problem on pavement, and could cause some damage to the transaxle and/or axles. The diagnostic capability that it provides can reduce diagnostic time. And there seems to be a certain comfort for a Syncro driver when they can see a pending diff-lock engagement.

Parts List:

 Vacuum Sensor Switch connected to Blinker Circuit Board

 3 Blue crimp-on female connectors

 Tie wraps for securing circuit board and switch

 These instructions

Required tools:

 Phillips screwdriver.

 Pliers.

Terminology: Each diff-lock mechanism is controlled by 4 switches and a lot of vacuum line. There is a vacuum line coming off of the brake booster line in the engine compartment. This feeds into a one way valve (to maintain vacuum in the diff-lock system) along with a vacuum reservoir under the car. There is a tee in this line that routes under the car and comes into the passenger compartment under the Diff-Lock Panel, which has one, two, or three Vacuum Dash Switches, controlling the Front-Diff, the Decoupler, and/or the Rear-Diff. The Vacuum Dash Switches control vacuum to the Vacuum Control Units on the differential or transmission. There is also a Contact Switch that senses engagement. Finally there is a Vacuum Sense Switch for the blinker unit included with the kit that you will be installing.

Detailed Instructions:

The Blinker Unit with Switch can be installed on either the front diff-lock, rear diff-lock, or decoupler system by tapping into existing original front diff wiring harness installed originally on all Syncros. This Add-on unit is meant to be added as the second blinker control in the front dash panel.

Make sure (before starting the procedure) that the diff-locks are working properly. Take your Syncro for a drive, and engage the diff-locks (on dirt, not pavement) and verify that they are functional and that the corresponding dash lights come on. Disengage the diff-locks and drive it into to your work area. Put your Syncro in neutral, and pull the diff-lock Vacuum Dash Switches. If either or both dash lights come on, then push the knobs back in, drive around the block, and try again. You are attempting here to get the diff-locks into "engaging" mode, not "engaged" mode (solid light). Now that the diff-lock splines are NOT engaged, shut off engine, set the emergency brake, and begin installation.

Pull off knobs on the existing diff-lock switch by holding the shaft with smooth pliers (use tape on the plier's surfaces if necessary) and unscrewing the knobs.

Remove the four screws securing the Syncro diff-lock panel onto the center console.

Now undo the gold metal bracket and pull out a ways to provide some working room.

Remove lower plastic shroud by pulling straight back; check clearance on top edge.

On the target diff-lock or decoupler Dash Vacuum Switch locate the vacuum switch nipple that connects to the rubber tube that is closest to the knob. Separate the corresponding plastic line from the rubber line (usually in the shape of a J), and insert the separated ends into the opposite ends of the Y.

In the nest of wiring under the dash that runs to the lighted panel on the Dash Vacuum Switch unit, there is a six-wire connector that connects to the printed circuit board in the dash panel that holds the diff-lock dash panel lights. One of the wires in this connector is a solid brown wire. Attach the brown wire from your add-on unit to this connector, using a blue tap connector. Attach the blue crimp-on female connector using a pair of pliers - you will know it is crimped properly when the little latch on it is closed. Next, locate the blue wire with a black stripe that goes to six-wire connector. Attach a blue tap connector onto this wire and attach the corresponding blue/black wire from the blinker circuit to this connection. Finally, choose the wire that corresponds to the circuit you want to add the blinker to, tap into that line with a blue tap connector, and attach the blue wire with red stripe to that connection (white with black stripe wire is the front diff, blue with brown stripe wire is the rear diff, and brown with black stripe is the decoupler). Use the enclosed tie-wrap to secure the Vacuum Sense Switch and Circuit Board to the bundle of vacuum lines.

Now that your new blinker is installed, you should test it before putting the dash back together. Make sure that all the wire and vacuum lines are connected. Put the van in neutral, and start the engine. Let the vacuum build for up to a minute or so (may be necessary if your rubber vacuum lines have gotten a bit stiff and leaky with age). Then pull your dash switch. As we know (from the first step in this procedure) that it should be in "engaging mode", the light should be blinking. If so, we are done. If not, go back over the procedure and verify that everything is connected properly.

Replace bracket and panel being careful to not kink vacuum lines or pinch wiring. Start engine once again, and verify that dash light is blinking once the knob is pulled.

Enjoy your Syncro!!!!

Technical assistance or comments:

E-mail: (subject: blinker)